Vacuum cleaners are very useful in keeping your living space clean. Dyson is a trendy and popular vacuum cleaner brand. Their vacuums are known for being powerful and easy to use. However, over time, the vacuum head can become quite dirty and need to be cleaned.
According to the report of a study published by the National Center for Biotechnology Information, it was found that the average American home contains about 100 dust mites. That’s a lot of dust! And it’s not just dust that can accumulate on your vacuum head.
It means that it’s important to clean your vacuum head regularly to ensure that it’s working properly and not just pushing around dirt and dust. But how do you clean a Dyson vacuum head?
Because there are so many small parts on a Dyson vacuum head, it can be a bit tricky to clean. That’s why you need to read this article completely. Because in this article I have shared a step-by-step process to clean the Dyson vacuum head.
Also, I have covered some important instructions that you should understand before doing anything else with your Dyson vacuum head.
Table of Contents
Instructions Before Cleaning Dyson Vacuum Head
Dyson vacuum cleaners are always a great choice to have in your home. They offer powerful suction and are designed to clean a variety of surfaces. But when it comes to cleaning the vacuum head, there are a few things you need to keep in mind.
- Unplug the vacuum cleaner from the power outlet before starting to clean the head.
- Use a soft cloth or brush to gently remove any dirt or debris from the vacuum head. Do not use any harsh chemicals or cleaners on the head as this can damage it.
- If the vacuum head is very dirty, you may need to soak it in warm water with a mild detergent.
- Rinse the head well and dry it completely before using the vacuum again.
- Do not use the vacuum without the head in place as this can damage the machine.
By following these simple instructions, you can keep your Dyson vacuum head in top condition and ensure it lasts for many years.
How To Clean Dyson Vacuum Head: Step By Step Process!
Cleaning the Dyson vacuum head is quick and easy, and only takes a few minutes. Here is a step by step guide on how to clean your Dyson vacuum head:
1. Turn Off Your Vacuum & Unplug It From The Wall
Vacuum cleaner heads can be full of dust and debris. Also, it might be very hot if you’ve just used it. To avoid injury, always unplug your vacuum from the wall and make sure it’s turned off before you start cleaning it.
Usually, the vacuum head can be turned off by a switch on the body of the vacuum itself. If your model has a cord wrap, you may need to use the switch on the cord wrap to turn off your vacuum.
2. Remove The Dustbin & Empty It Into The Trash Can
A dustbin is the part of a vacuum cleaner where dirt and dust are collected. It’s usually located at the front or top of the vacuum. To remove the dustbin, press the release button and lift it out. Then, empty the contents into a trash can.
In some models, it can be located on the side or back of the machine. So you need to check your user manual to see where it is located on your machine. If you have a problem with your machine, please call the Dyson Helpline.
3. Remove The Screws That Hold The Vacuum Head In Place
Locate the screws that hold the vacuum head in place. There are usually two screws, one on each side. Use a screwdriver to remove these screws. Make sure to keep track of where the screws go, as you will need to put them back in later.
However, if your model has a locking tab instead of screws, simply depress the tab to release the vacuum head. I know it might be a little different from what you’re used to, but it will make things a lot easier in the long run.
4. Gently Pull The Vacuum Head Off Of The Main Unit
The vacuum head is the part of the vacuum cleaner that comes into contact with the floor or carpet. It is responsible for sucking up dirt, dust, and debris. So after removing the screws and dustbin from your Dyson vacuum cleaner.
Now, you need to take off the vacuum head. For this, you need to grab it from the top and pull it towards yourself. You can also check the manual for specific instructions on how to remove the vacuum head.
5. Use A Brush To Clean Out Any Dirt Inside Of The Bristles
The bristles inside the vacuum head are used to help clean the floors. They are made of different materials depending on the model of the Dyson vacuum you own. Use a brush to clean out any dirt that may have accumulated inside the bristles.
Be sure to remove any hair or debris that may be stuck in the bristles as well. But make sure not to use a brush with metal bristles, as this can damage the vacuum head. Or it might come with a cleaning tool.
6. Wipe Down The Entire Surface Of The Vacuum Head
A damp cloth is a cloth that has been slightly wetted with water or another liquid. Use a damp cloth to wipe down the entire surface of the vacuum head. This includes the top, bottom, and sides of the vacuum head.
Make sure to remove any dirt, dust, or debris that may be on the surface of the vacuum head. Because the Dyson vacuum head is made of plastic, it is important to avoid using any harsh chemicals or cleaners on the surface of the vacuum head.
7. Remove The Filters & Wash Them In Warm, Soapy Water
A filter in a vacuum cleaner is a device that removes particles from the air as it is being sucked into the machine. This helps to improve the suction power of the vacuum and also prevents dirt and dust from being blown back into the room.
So now you need to remove the filter of your Dyson vacuum cleaner. Most Dyson vacuum cleaners have two filters – a ‘pre-motor’ filter and a ‘post-motor’ filter. Make sure you know where each filter is located before you start.
8. Shake Out Any Excess Water & Let Them Air Dry
After you have removed the filters, shake out any excess water and then let them air dry. It is important that you do not put the filters back into the vacuum until they are completely dry, as this could damage the machine.
You can also clean the inside of the vacuum head by using a soft brush. Or, if you have a detachable hose, you can remove it and wash it in warm, soapy water. But it might be a good idea to check the user manual first, as some models of vacuum cleaners do not have a detachable hose.
9. Replace The Screws & Reattach The Vacuum Head To The Main Unit
The main unit in a vacuum cleaner is the body of the machine. This is where the motor, filter, and dustbin are located. The vacuum head is the part of the machine that actually does the work of suctioning up dirt and debris.
It is usually attached to the main unit by a hose or a cord. In order to clean the vacuum head, you will need to first detach it from the main unit. Then after completing the work mentioned above. You need to reattach all the screws and vacuum head to the main unit.
10. Reattach The Dustbin & Plug-In Your Vacuum Cleaner.
The dustbin is the part of the vacuum cleaner that collects the dirt and debris that is suctioned up. To reattach it, simply push it back into place until it clicks. Then, take the power cord and plug it into an outlet.
Make sure that the cord is fully inserted into the outlet, as a loose connection can cause the vacuum to lose power. Otherwise, your vacuum should now be turned on and ready to use. Now your vacuum cleaner is ready to use!
Other Parts That Should Clean With Dyson Vacuum Head
The vacuum cleaner itself is a cleaning machine. But, as with any other machine it is combined with many moving mechanical parts. That requires regular cleaning and maintenance to keep the machine running smoothly. The main parts of a vacuum cleaner that require regular cleaning are:
- The brush roll: The brushroll is responsible for agitating the floor to loosen dirt and debris. It also helps to move dirt and debris towards the vacuum head. The brush roll should be cleaned on a regular basis to ensure that it can continue to do its job properly.
- The hose: The hose is responsible for carrying dirt and debris from the vacuum head to the dustbin. If the hose becomes clogged, it can prevent the vacuum from working properly. The hose should be cleaned on a regular basis to ensure that it is clear of any obstruction.
- The filter: The filter is responsible for trapping dirt and dust particles that are sucked up by the vacuum. The filter should be cleaned on a regular basis to prevent it from becoming clogged and ineffective.
How Often Should You Clean Your Dyson Vacuum Head?
It is important to keep your vacuum head clean in order to maintain suction power and prevent dirt and dust from clogging the moving parts. Depending on how often you use your vacuum, you should clean the head every one to three months.
If you find that your vacuum isn’t picking up as much dirt as it used to, or if the head feels clogged, it’s probably time for a cleaning. However, it might be necessary to clean more frequently if you have pets or live in a dusty environment.
So if you are living in a dusty environment or have pets at home, you should clean your vacuum head every month or two. On the other hand, if neither of these things applies to you, you can probably get away with cleaning it every three months or so.
Is Your Dyson Vacuum Head Smell Really Bad?
If your Dyson vacuum head smells bad, don’t panic! There might a lot of dirt and debris building up inside the vacuum head, causing it to stink. If you want to get rid of this smell then you need to clean your Dyson Vacuum head.
Or you can also replace your Dyson vacuum head with a new one. Also, it will be a good idea to check your vacuum regularly and clean it out often, to avoid the bad smell.
Wrap Up On How To Clean Dyson Vacuum Head
Regular cleaning and maintenance of your vacuum cleaner is essential for keeping it running smoothly. The main parts that require regular cleaning are the brush roll, hose, and filter. Depending on how often you use your vacuum, you should clean the head every one to three months.
However, I have shared the instructions on how to clean the vacuum head, if you want to get rid of the bad smell. You should also check your vacuum regularly and clean it out often, to avoid the bad smell. Thanks for reading!
FAQ: 10 Steps To Clean Dyson Vacuum Head Easily
Cleaning the Dyson Vacuum head is quite tricky. That’s why many people just like you have lots of questions. That can be solved easily. That’s why I have added some of them in this article to provide appropriate answers to them.
Q1. How do I remove the dirt from inside the vacuum head?
Ans: You need to unscrew the three screws that are holding the soleplate. After that, you will be able to see the dustbin. Just remove it and empty it.
Q2. What can I do if there’s hair stuck in the vacuum head?
Ans: If you have long hair, then it is bound to get wrapped around the beater bar of your vacuum cleaner head. To remove this, you’ll need to first detach the beater bar and then cut away the hair that’s wrapped around it.
Q3. How much time does it take to clean the Dyson vacuum head?
Ans: It usually depends on the type of Dyson vacuum you have. If you have the cordless one then it might take a bit longer. However, on average, it takes around 20-30 minutes to clean the vacuum head.
